Binding Machines Buying Guide

Question by TERRY K: Is anybody knowledgeable on dishwashers?
The lower spraybar on my Maytag dishwasher doesn’t rotate. It remains in pretty much one position during the entire wash cycle. There isn’t anything binding against it and it is free to rotate; I can spin it by hand. I really can’t determine how much water is actually coming out of it. The machine is about ten years old. Any ideas from the appliance gurus out there?

Best answer:

Answer by samfrio
When this happened to me, it was turning by hand; but not freely enought to spin properly.
It’s a little messy, but you should be able to manipulate the door catch so that the washer can turn on with the door ajar. Doing so will allow you to see how much water comes out of the spraybar.
Otherwise, if you haven’t yet, make sure there’s no trash in the intake on the bottom of the washer that might be restricting pump flow.

What do you think? Answer below!

Question by Jen K: I have a singer knitting machine (the kids pink one) with no instructions… any help??
I need to know how to cast-on, bind off and switch from round to flat mode (it feels like the switch may be stuck) Thanks!!!!

Best answer:

Answer by maJiCMan
Try a google or yahoo search with the manufacturer and model and words like “owners manual” or “instruction manual”. You might get lucky and find one online.

Good luck.

j

Give your answer to this question below!

Question by Susan: Is this a binding contract?
Susan
Level 1
contract law?
I signed a contract with a datings service. Less than three days later, they said they lost the signature page and asked me to resign. I didn’t resend them anything and no service has been provided to date. However, they did hound me to send them the signature page again. Because they were so unprofessional, I decided I didn’t want to proceed and told them not to expect anything from me. 3 weeks later, the manager of the service called me and said she found the signature page and that I was obligated to use their service. BTW, when I signed the original contract she said she would send me my copy because the copy machine was broke…I know…dumb on my part. Since I have in writing that they said they didn’t have a contract….am I still bound by this contract? I did subsequently send them a certified letter after she said she “found the signature page” and said I was exercising my 72 hr. window for cancellation.

Best answer:

Answer by suzzieq175
a dating service?? no binding contract unless you signed a conract, if they lost the signaure page..ooppps sounds like they are trying to lure you in again. demand that she send you a copy of the signature page. if you have never recieved the signature copy then its not binding. she sounds like a shady lady

Add your own answer in the comments!

Question by RoB: Why when you sew on thick material with a zig-zag machine does the thread tend to flag on the right side?
I am a sewing machine mechanic and I run into all kinds of problems but these ZZ machines are tough to figure out ! First of all, our ZZ’s are set up with core edge folders and and we run material anywhere from 1/64 to 3/16 thick. Now combined with the binding thats pretty thick! The thicker the material the more the thread flags and skips on the right side. I know that putting pressure on the foot and rising the needle bar along with timing the hook as close to the eye of the needle as possible helps, but there has got to be a better way. I am looking for any ideas I could try.

Best answer:

Answer by kay
Thread or needle lubricant, or lower elasticity of the thread might help, too.

Give your answer to this question below!

Question by Georgie G: how can i improve my machine deck?
i would like to create a strong machine deck. for fusion i have cyber end dragon, cyber twin, and gatling dragon. i have one synchro, turbo cannon.(i think i should take it out)

for monsters i have
3x proto cyber dragon
cyber dragon
copycat
turbo rocket
3x cyber phoenix
2x dekoichi the battlefield locomotive
barrel dragon
blowback dragon
JINZO

spells:
limiter removal
power bond
twister
overload fusion
mst
future fusion
heavy storm
polymerization
scapegoat
lightning vortex

taps:
2x sakuretsu armor
spell binding circle
SCrap iron scarecrow
solemn judgemen

i want to create a deck that will let me utilize all of my fusion monsters
should i take out turbo cannon and turbo rocket since they seem useless, along with copycat?

For monsters,i want to add a reflect bounder, king of the swamp, and light hex sealed fusion.

For trap cards i want to add: royal decree, mirror force, waboku, and a imperial iron wall. my friend has a dd deck

and for spells should i add: shrink, swords of revealing light, windstorm of etaqua, and brain control.

would it be good to add these cards.

please advise me on which cards to take out and which to add.

im new to yugioh

Best answer:

Answer by Zen
All the ones you suggested to take out is correct, but you also need to take out Twister. After you take these out you should add “king of the swamp, swords of revealing light, mirror force, waboku, and possibly pot of avarice. i have at least six years of experience and hope this helps. your suggestions were really good and i think you would end up being an even better duelist with a more advanced deck. Like Black wings and Gemini.

Know better? Leave your own answer in the comments!